X9 Owners & Riders Club
October 24, 2021, 21:31:35 *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Website Gallery Login Register Donate  
Pages: [1]   Go Down
  Print  
Author Topic: Help with a tool please!  (Read 6221 times)
poldark
Stunt Rider
****
Offline Offline

Posts: 1490


St Albans, Herts


« on: April 24, 2009, 13:39:27 »

Calling anyone who's near North London and especially anyone attending at the Ace tomorrow morning for brekkie, I'm grovelling for a favour.

I need to borrow (or even buy) a 19mm hex key, so I can undo the front wheel axle on my TDM, as I'm sending off the forks for rechroming and need to strip them down this weekend.

Everywhere I've looked wants circa £20 for a jumbo hex key set and I can't seem to find anywhere local that can supply the single hex key. 

Given I need it for (hopefully) only 5 mins to undo the front wheel, plus another 5 mins in 2-3 weeks time when I get the newly chromed forks back, I'd rather not spend so much.

So if anyone can lend me one or has a spare individual key I can purchase or maybe knows somewhere I could pick one up this Sat I'd be really gratful.

Thanks very much
Logged

Honda NC750X DCT ('17)
jimc
Club Elder
Old Timer
*****
Offline Offline

Posts: 15696



WWW
« Reply #1 on: April 24, 2009, 13:52:06 »

Any bike dealer should have a 'multi-tool' with four large hex sections for about a fiver.  You then use a socket on the other end.  Very standard bike kit.
Logged

Jim Crowther
GT200L (The Hornet), GTS300 (in CA)
Dave Milnes
Administrator
Old Timer
*****
Offline Offline

Posts: 21060


Fylde Coast


WWW
« Reply #2 on: April 24, 2009, 16:02:11 »

You might not even need one to get the wheel out. If you leave the lock screws nipped while you release the nut on the end of the axle, then slacken them and tap the shaft out.
Logged

2004 X9 500 Evo in YELLOW - 2016 Maxsym 600i Sport
Anderton 2004, Pen-y-cae 2005, Matlock 2006, Hay on Wye 2007, Minehead 2008, St Florence 2010, Newent 2011, North Kyme 2012, Betsw-y-coed 2013, Hardraw 2014, Parkend 2015, Whitby 2016, Mundesley 2017, Derby 2018, Telford 2019, Loch Doon 2020.
poldark
Stunt Rider
****
Offline Offline

Posts: 1490


St Albans, Herts


« Reply #3 on: April 24, 2009, 16:16:15 »

Thanks Dave I'll take a look but I'm pretty sure that the axle bolts directly into the base of the r h fork and there's no nut I can undo, certainly looks that way on the workshop manual, but I haven't had a close look yet.

Tried Jims suggestion and called some local bike dealers (Slocombes, Rex Judd, Southern Cross) but they either don't do tools or don't have one in stock.  I did get a strong recommendation for a bike spares place that's very local, but would you believe they shut on a Fri afternoon, so I'll have to call them in the morning.
Logged

Honda NC750X DCT ('17)
jimc
Club Elder
Old Timer
*****
Offline Offline

Posts: 15696



WWW
« Reply #4 on: April 24, 2009, 17:58:28 »

Martyn, if I remember I'll buy one in the morning at CBS Whitton and bring it to the Ace.  Alarm clocks willing etc...
Logged

Jim Crowther
GT200L (The Hornet), GTS300 (in CA)
Dave Milnes
Administrator
Old Timer
*****
Offline Offline

Posts: 21060


Fylde Coast


WWW
« Reply #5 on: April 24, 2009, 20:15:21 »

Sorry I thought it was an X9.
Read again...TDM so I guess it's similar to the Tmax where the axle passes through the RH strut and screws into the LH strut directly.
I found a bolt with the right size head to fit in the axle and with a short spacer under the head, locked it with a pair of nuts tightened so their flats lined up. Using this and a socket I managed to get the axle out. Jim's solution is probably better though!
Logged

2004 X9 500 Evo in YELLOW - 2016 Maxsym 600i Sport
Anderton 2004, Pen-y-cae 2005, Matlock 2006, Hay on Wye 2007, Minehead 2008, St Florence 2010, Newent 2011, North Kyme 2012, Betsw-y-coed 2013, Hardraw 2014, Parkend 2015, Whitby 2016, Mundesley 2017, Derby 2018, Telford 2019, Loch Doon 2020.
spannerman
Stunt Rider
****
Offline Offline

Posts: 3733



« Reply #6 on: April 25, 2009, 08:23:39 »

I use a double sided car sump plug hex, http://www.lasertools.co.uk/item.aspx?cat=295&item=417
It fits tmax spindle, should do a TDM 17mm?
Logged

Dave Weller, Chatham
NC750S 2016. FJS600. Silverwing 2010.
poldark
Stunt Rider
****
Offline Offline

Posts: 1490


St Albans, Herts


« Reply #7 on: April 25, 2009, 13:31:18 »

Thanks all, I'm borrowing a key for tomorrow from a mate and have ordered a suitable wheel axle socket from Busters, so I have my own and will use this to re-install when I get the newly chromed forks back in about 3 weeks time.

http://www.busters-accessories.co.uk/productInfo.aspx?catRef=ASA17-19&kw=axle+socket
Logged

Honda NC750X DCT ('17)
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!